Densacrete Hybrid
A water-based concrete densifier combining potassium and lithium silicates for faster, deeper penetration — hardens, dust-proofs and colour-enhances concrete floors leaving no efflorescence.
- Deep penetration and fast reaction with concrete for durable protection
- Leaves no visible efflorescence after treatment
- Hardens concrete and reduces surface permeability
- Increases surface strength and seals from dusting
- Enhances concrete colour without changing surface characteristics
- Ready-to-use or dilute with water
- Zero VOC — water-based and environmentally friendly
Surface PreparationThoroughly clean the concrete surface to remove any contaminants that may block Densacrete Hybrid from penetrating effectively. Ensure the surface is completely dry before application. Properly cure new concrete before treatment. Remove all curing compounds, release agents and surface coatings or membranes, then clean and dry the area. For acid-treated concrete, neutralise the surface, rinse with water and allow to dry fully. For polished concrete, grind to 200 grit or desired finish to expose capillaries and maximise sealer absorption.Application Method1Mix Densacrete Hybrid thoroughly before use. Apply as a ready-to-use sealer or dilute with clean water if required.2Use a low-pressure hand sprayer, brush or broom to evenly flood the surface. Avoid pooling. Maintain a mirror-like wet film for up to 30 minutes to ensure maximum absorption.3If the surface absorbs the first coat quickly, immediately apply a second coat using the wet-on-wet method. For porous concrete, repeat until the surface reaches saturation.4Remove any excess product remaining unabsorbed after 30 minutes to prevent surface residue formation.5After full cure and drying, polish or buff the concrete to achieve the desired finish. Reapply Densacrete Hybrid after each polishing cycle to enhance densification.Suitable SurfacesResidential concrete floorsCommercial car park flooringFactory and warehouse concrete slabsNew and old concrete requiring dust-proofingNatural stone, clay bricks and ceramic tiles (test first)Coverage Rate5–20 m² per litre per coat — varies significantly depending on concrete porosity. Dense or new concrete absorbs less while porous or old concrete absorbs more.Pro Tip: For added protection against water and oil, apply Tech-Dry’s water and oil-resistant densification sealer or a compatible repellent as a topcoat following the final polish. Allow at least 24 hours before heavy traffic exposure. Full densification typically develops over 7 days.
| Coverage Rate | 5–20 m²/litre/coat (varies by concrete porosity) |
| Packaging | 20L, 200L & 1,000L packages |
Download the full product data sheet for detailed technical information, safety data, and application guidelines.
Download Data Sheet (PDF)- Deep penetration and fast reaction with concrete for durable protection
- Leaves no visible efflorescence after treatment
- Hardens concrete and reduces surface permeability
- Increases surface strength and seals from dusting
- Enhances concrete colour without changing surface characteristics
- Ready-to-use or dilute with water
- Zero VOC — water-based and environmentally friendly
Surface PreparationThoroughly clean the concrete surface to remove any contaminants that may block Densacrete Hybrid from penetrating effectively. Ensure the surface is completely dry before application. Properly cure new concrete before treatment. Remove all curing compounds, release agents and surface coatings or membranes, then clean and dry the area. For acid-treated concrete, neutralise the surface, rinse with water and allow to dry fully. For polished concrete, grind to 200 grit or desired finish to expose capillaries and maximise sealer absorption.Application Method1Mix Densacrete Hybrid thoroughly before use. Apply as a ready-to-use sealer or dilute with clean water if required.2Use a low-pressure hand sprayer, brush or broom to evenly flood the surface. Avoid pooling. Maintain a mirror-like wet film for up to 30 minutes to ensure maximum absorption.3If the surface absorbs the first coat quickly, immediately apply a second coat using the wet-on-wet method. For porous concrete, repeat until the surface reaches saturation.4Remove any excess product remaining unabsorbed after 30 minutes to prevent surface residue formation.5After full cure and drying, polish or buff the concrete to achieve the desired finish. Reapply Densacrete Hybrid after each polishing cycle to enhance densification.Suitable SurfacesResidential concrete floorsCommercial car park flooringFactory and warehouse concrete slabsNew and old concrete requiring dust-proofingNatural stone, clay bricks and ceramic tiles (test first)Coverage Rate5–20 m² per litre per coat — varies significantly depending on concrete porosity. Dense or new concrete absorbs less while porous or old concrete absorbs more.Pro Tip: For added protection against water and oil, apply Tech-Dry’s water and oil-resistant densification sealer or a compatible repellent as a topcoat following the final polish. Allow at least 24 hours before heavy traffic exposure. Full densification typically develops over 7 days.
| Coverage Rate | 5–20 m²/litre/coat (varies by concrete porosity) |
| Packaging | 20L, 200L & 1,000L packages |
Download the full product data sheet.
Download PDF